Snyder Advantage Plates Directions

Snyder Advantage roller skate plates are professional models designed for advanced level skating applications, such as roller derby or artistic dance. Constructed of extremely light aircraft-grade aluminum, Advantage plates install on existing or new boots and are interchangeable with all Snyder Deluxe trucks. They feature click action truck adjustment and 5/8-inch adjustable jump stops. Snyder Advantage skate plates are sized according to the size of the boot on which they will be installed.\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\tThings You'll Need
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\tDrill
\t\t\t\t\t\t\t\t\t\t\t\t\t\t7/32-inch drill bit
\t\t\t\t\t\t\t\t\t\t\t\t\t\tOpen-end wrenches
\t\t\t\t\t\t\t\t\t\t\t\t\t\tPunch or awl
\t\t\t\t\t\t\t\t\t\t\t\t\t\tWooden mallet
\t\t\t\t\t\t\t\t\t\t\t\t\t\t120-grit sandpaper
\t\t\t\t\t\t\t\t\t\t\t\t\t\tDremel tool with grinding wheel or hammer and punch
\t\t\t\t\t\t\t\t\t\t\t\t\t
\t\t\t\t\t\tShow More\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t \t\t\t\t\t\t\t\t\t\tInstructions
\t \t\t\t\t\t\t\t\t\t\t\t\t\t\t\t
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t1\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t

Remove the truck assemblies from the king pins on both plates by releasing each king pin locknut with an 11/16-inch open-end wrench, then unscrewing the king pin.
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t2\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t

Sand the heel and toe of each boot with 120-grit sandpaper and verify that they are level.
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t3\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t

Draw the center line on each boot. Determine the center of the heel and make a mark at that point. Draw a line across the widest portion of the sole of the boot with a pencil, measure the line and make a mark at the center point. Draw a straight line the length of the boot, intersecting those two points.
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t4\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t

Position the plate on the boot, aligning the center line marks on the plate with the center line on the boot.
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t5\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t

Adjust the plate forward or backward to position the front axle beneath the ball of the foot and the rear axle beneath the heel. Mark the position of the front mounting holes in the plate with a pencil.
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t6\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t

Strike the plate with a wooden mallet to inscribe rivet marks on the sole of the boot.
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t7\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t

Use a punch, awl or other sharp object to enlarge the mounting holes and the rivet marks in the sole of the boot.
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t8\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t

Drill a shallow, 7/32-inch hole at each rivet mark, just deep enough to permit the rivet head to recess into the sole. Drill 7/32-inch holes all the way through the sole at the front mounting hole marks. Countersink the front mounting holes to make room for the mounting cups.
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t9\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t

Insert the small bolts and mounting cups through the front mounting holes but do not tighten yet.
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t10\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t

Drill 7/32-inch holes all the way through the sole at the rear mounting hole marks.
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t11\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t

Insert long bolts and lock washers through the rear mounting holes but do not tighten yet.
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t12\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t

Verify that the plate center line is still aligned with the center line mark on the sole of the boot.
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t13\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t

Tighten all bolts. Snap off the portion of the bolt that protrudes above the nut. Use a Dremel tool with a grinding wheel or a hammer and punch to round off or blunt any sharp edges on the top of the bolts.
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t14\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t

Reinstall the truck assemblies by screwing in the king pins and tightening the king pin locknuts with an 11/16-inch open-end wrench.
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t
\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t
\t\t\t\t\t\t
\t\t\t\t\t
\t\t\t\t\t
[Snyder Advantage Plates Directions: https://da.sportsfitness.win/fritid/rulleskøjter/1003001905.html ]